NEWS
 

  1. Welcome to Veloster Forum: Hyundai Veloster / Veloster Turbo Forums – General discussion forum for Hyundai Veloster

     
+ Reply to Thread
Results 1 to 9 of 9

Thread: Torque Solutions exhaust hanger kit

  1. #1
    Senior Member
    Join Date
    Oct 2011
    Posts
    211

    Torque Solutions exhaust hanger kit

    available from www.AWDMotorsports.com

    torque solutions exhaust hanger kit.

    Same type bushing as one i have for lower trans mount and shifter linkage

    Easy to install eliminates sagging/excess movement :]


    Sent from my Galaxy Nexus using AutoGuide.Com Free App
    Attached Thumbnails Attached Thumbnails Torque Solutions exhaust hanger kit-uploadfromtaptalk1352859883032.jpg   Torque Solutions exhaust hanger kit-uploadfromtaptalk1352859896904.jpg   Torque Solutions exhaust hanger kit-uploadfromtaptalk1352859907422.jpg   Torque Solutions exhaust hanger kit-uploadfromtaptalk1352859914894.jpg   Torque Solutions exhaust hanger kit-uploadfromtaptalk1352859946953.jpg  

    Optima Turbo Front Brake Upgrade,Rear Sway Bar,Front Strut Bar,NGM Lowering Springs ,15mm Spacers all round ,35% tint all around,HID 6000k,Dipped emblems,BLOX Velocity Stack Intake,Torque Solutions Lower Trans(dog bone) Mount,Torque Solutions shifter linkage Bushings,Torque Solutions Exhaust Hanger Kit, Magnaflow Exhaust,TurboSocks FMIC,TurboSocks 3" SRI,SFR Rigid Collar Kit,NGK Iridium plugs(here),Hawk HPS pads(here) Redline MTL-->MT90 trans fluid(here), "TEE" Vacuum line mod

  2. Remove Advertisements
    Hyundai Veloster
    Advertisements
     

  3. #2
    Super Moderator RPW00Mirage's Avatar
    Join Date
    Jun 2012
    Location
    Central MA
    Posts
    1,207
    now this i am not sure of. sure, maybe on a heavier exhaust or as an upgrade to replace ancient hangers but the pipes on the veloster don't move much if at all. maybe they move more with the urethane torque mount installed. hmmmm......
    2012 Boston Red Veloster base

  4. #3
    Senior Member
    Join Date
    Oct 2011
    Posts
    211
    more it flexes it will wear out and cause a sag

    not really a performance upgrade but its still cool

    next up on my list is the rear torsion beam bushing

  5. #4
    Super Moderator GreyGhost12's Avatar
    Join Date
    Dec 2011
    Location
    Northeastern NY
    Posts
    2,759
    While urethane exhaust bushings are cool and do just as they are intended to do, I wouldn't bother replacing the stock bushings until they broke or wore out. At that point for a few extra dollars you might as well get the urethane components over the plain rubber units. You won't have to worry about them again at that point.

  6. #5
    Senior Member
    Join Date
    Oct 2011
    Posts
    211
    i noticed few genesis coupe peoples hanger being saggy only after a year or so...

    Main reason why i got it was the center bar brace was touching the muffler when it was warm(slightly vibrating at stop) but not when it was cold. bushings were softening up so there was more play.

    This one no more rattle.

    Sent from my Galaxy Nexus using AutoGuide.Com Free App
    Optima Turbo Front Brake Upgrade,Rear Sway Bar,Front Strut Bar,NGM Lowering Springs ,15mm Spacers all round ,35% tint all around,HID 6000k,Dipped emblems,BLOX Velocity Stack Intake,Torque Solutions Lower Trans(dog bone) Mount,Torque Solutions shifter linkage Bushings,Torque Solutions Exhaust Hanger Kit, Magnaflow Exhaust,TurboSocks FMIC,TurboSocks 3" SRI,SFR Rigid Collar Kit,NGK Iridium plugs(here),Hawk HPS pads(here) Redline MTL-->MT90 trans fluid(here), "TEE" Vacuum line mod

  7. #6
    Super Moderator RPW00Mirage's Avatar
    Join Date
    Jun 2012
    Location
    Central MA
    Posts
    1,207
    ^^ that makes total sense then!
    2012 Boston Red Veloster base

  8. #7
    MTD
    MTD is offline
    Senior Member MTD's Avatar
    Join Date
    Aug 2010
    Location
    ON, CAN
    Posts
    3,670
    Why isn't any of this stuff on the website? Am I blind lol.
    '13 VT

  9. #8
    Senior Member
    Join Date
    Oct 2011
    Posts
    211
    Optima Turbo Front Brake Upgrade,Rear Sway Bar,Front Strut Bar,NGM Lowering Springs ,15mm Spacers all round ,35% tint all around,HID 6000k,Dipped emblems,BLOX Velocity Stack Intake,Torque Solutions Lower Trans(dog bone) Mount,Torque Solutions shifter linkage Bushings,Torque Solutions Exhaust Hanger Kit, Magnaflow Exhaust,TurboSocks FMIC,TurboSocks 3" SRI,SFR Rigid Collar Kit,NGK Iridium plugs(here),Hawk HPS pads(here) Redline MTL-->MT90 trans fluid(here), "TEE" Vacuum line mod

  10. #9
    Super Moderator GreyGhost12's Avatar
    Join Date
    Dec 2011
    Location
    Northeastern NY
    Posts
    2,759
    My cheap fix to slighty saggy and swingy exhausts in times past was a few extra ty-wraps holding the rubber double-donuts in place. This is a far better solution to the problem.

  11. Remove Advertisements
    Hyundai Veloster
    Advertisements
     

Quick Reply Quick Reply

Register Now

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.


Similar Threads

  1. Torque Solutions M/T bushing
    By HyundaiVeloster in forum Hyundai Veloster Turbo Discussion
    Replies: 22
    Last Post: 04-18-2013, 07:20 PM
  2. Torque
    By dissa in forum Hyundai Veloster Engine and Transmission
    Replies: 4
    Last Post: 09-27-2012, 05:34 PM
  3. Anyone have solutions for gun storage?
    By smellypanda in forum Off Topic Discussion
    Replies: 34
    Last Post: 07-20-2012, 10:50 PM

Tags for this Thread

Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
Powered by vBadvanced CMPS v4.1.2